Discussion in "Project Help" started by    Ansh12    Mar 22, 2019.
Sun Apr 28 2019, 02:15 PM
#11


I made a minor change, it works in Proteus.
Try the attached hex code, just in case you have a compiler problem.

Are you sure you are getting a good signal into pin RB0 ?

if(INTF==1)
    {
         RD4 = 1;  // LED ON
         __delay_ms(1000); // 
         RD4 = 0;  // LED OFF
         __delay_ms(1000); // 
         
         INTF = 0;
    } 


ExperimenterUK



you are absolutely right. I reinstalled MPLABX IDE and my previous program is working now

Now all is working so I want to do little changes

I have one sensor when it triggered I want to start counting. How to do it ?

// CONFIG
#pragma config FOSC = HS        // Oscillator Selection bits (HS oscillator)
#pragma config WDTE = OFF       // Watchdog Timer Enable bit (WDT disabled)
#pragma config PWRTE = OFF      // Power-up Timer Enable bit (PWRT disabled)
#pragma config BOREN = ON       // Brown-out Reset Enable bit (BOR enabled)
#pragma config LVP = OFF        // Low-Voltage (Single-Supply) In-Circuit Serial Programming Enable bit (RB3 is digital I/O, HV on MCLR must be used for programming)
#pragma config CPD = OFF        // Data EEPROM Memory Code Protection bit (Data EEPROM code protection off)
#pragma config WRT = OFF        // Flash Program Memory Write Enable bits (Write protection off; all program memory may be written to by EECON control)
#pragma config CP = OFF         // Flash Program Memory Code Protection bit (Code protection off)
 
#define _XTAL_FREQ 20000000 //Specify the XTAL crystal FREQ
#include 
 
volatile unsigned int Counter;
char Trigger;
 
void main(void) 
{
    
    TRISB0=1;     // encoder as input
	
    TRISB1=1;     // Sensor as input
    TRISD1= 0;    // LED as output
    OPTION_REG=1;  // Set Rising Edge Trigger 
    INTCON = 1;   // Enable The Global Interrupt
    INTE = 1;     // External Interrupt Enable (not INTF)
    GIE=1;
    Counter = 0;  //initial values at start up
    Trigger = 0;
    
    while (1)
    {
        if(Trigger == 1)
        {
             Trigger = 0;
             Counter = 0;
            
             RD1 = 1;  // LED ON
             __delay_ms(1000); // 
             RD1 = 0;  // LED OFF
             __delay_ms(500); 
        }
    }
 
}
 
void interrupt isr(void)
{  
    if(INTF==1)
    {
        INTF = 0;  // Clear interrupt flag
        Counter++;    // add 1 to the Counter
        if(Counter == 30) 
        Trigger = 1;
    } 
}




[ Edited Sun Apr 28 2019, 02:17 PM ]

Get Social

Information

Powered by e107 Forum System

Conversation

Wed Apr 14 2021, 09:31 AM
Niklas Spearman
$99 once off!
Tue Apr 13 2021, 10:42 PM
Aliza Dyal
Brand new way of online advertising just released! The best part is you'll never have to pay for clicks again! To find out more have a look at : http://bit.ly/advertising-with-zero-perclick-charges-ever
Tue Apr 13 2021, 07:29 AM
Bryancxv
only
Mon Apr 12 2021, 11:54 AM
Joe N
I have recently launched my own site, and I am looking to provide value for you for free, by giving away 26 professional level blog post templates (worth $297).
Mon Apr 12 2021, 09:24 AM
Aretha
Hey, I think your site might be having browser compatibility issues. When I look at your website in Ie, it looks fine but when opening in Internet Explorer, it has some overlapping. I just wanted to give you a quick heads up! Other then that, very good blog! https://onanadiete.ru/alpha-numeric-reasoning-questions-and-answers-pdf.pdf alpha numeric reasoning questions and answers pdf alpha numeric reasoning questions and answers pdf

Downloads

Comments

Mirza123
Thu Jun 25 2020, 03:46 PM
eunicelove124
Mon Jun 22 2020, 03:03 PM
cerouno
Tue Jun 16 2020, 05:10 PM
Marce
Sat Jun 13 2020, 09:43 PM
Davidthils
Thu May 21 2020, 12:44 PM
Jakeror
Thu May 21 2020, 01:28 AM
motorCar
Wed May 20 2020, 07:05 PM
Vordrync
Wed May 20 2020, 11:52 AM

Online

Guests: 138, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38215
Newest member: Mirza123