Discussion in "Project Help" started by    venkat    Jun 22, 2007.
Fri Jun 22 2007, 06:28 AM
#1
hai friends,
please send me the schematic and c code to inteface the 12c887 rtc with at89c51ed2 mcu, waiting in anticipation
Tags interfacing 12C887 RTCinterfacing 12C887 RTC with 8051RTC interfacing
Fri Jun 22 2007, 08:10 AM
#2
I think one thread is already open for this discussion. Please do not make duplicate posts..
and make a schematic yourself i have also given you the pin configuration, if there is any error in the schematic i will help you correcting it.
and as it is memory mapped so you can simply read and write as you write in a memory location. first you finish your schematic then i will help you.

Note: Please do not create duplicate posts. If you have already opened a discussion with similar topic, its better to continue in the same thread Try not to mess up the forum.
Thanks!
Rickey's World
Fri Jun 22 2007, 08:57 AM
#3
Do you have assembly code for that?
Fri Jun 22 2007, 02:35 PM
#4
i said.. write the code if you get error i will help you removing it why you all want ready made things
Mon Jun 25 2007, 08:25 AM
#5
sir, Thank you for your replies,
I have already tried the circuit for dispalying the time on hyperterminal. I am getting the time which is not updating, for the first time i run the project i am getting whatever the time i have set without updating. if i switch off and on the controller i get another time which is still not updating. Even after i remove the rtc (i.e., po) iam still getting the un-updated time, in this case there is no connection between the rtc registers and the microcontroller. what could be wrong?
Mon Jun 25 2007, 09:10 AM
#6
no.. it could be cause.. you did not activate the oscillator. so clock is kind of halted.
see page 11 for more information on turning the oscillator on. :-)
Sat Jul 14 2007, 09:09 AM
#7
please refer "The 8051 microcontroller and Embedded System" By Mazidi." it has a very good tutorial for interface with 12c887 RTC
i have make a project using this with asm and working fine

note: before using the RTC u must enable the internal osc by proper configuration
Sat Jul 14 2007, 09:44 AM
#8
I told him to read page 11 and after that i am sure he will get the output.. coz he already made everything just for got to enable oscillator
Tue Jul 17 2007, 10:42 AM
#9
sir, I have enabled the oscillator, and used the attached code to read the initialized data and the updated clock. I am not getting the updated time. plz help me to debug.
Tue Jul 17 2007, 12:49 PM
#10
then post your work so that we can help u to find out the problem

Get Social

Information

Powered by e107 Forum System

Conversation

Thu May 06 2021, 01:11 PM
Karen
Hello, constantly i used to check blog posts here in the early hours in the morning, since i like to find out more and more. Local Dating https://datingsitesww.com
Thu May 06 2021, 12:33 PM
Shalanda
It's an remarkable article in support of all the web people; they will get benefit from it I am sure. senior dating sites http://onlinedatingdd.com/
Thu May 06 2021, 10:24 AM
Felisha
What's Taking place i am new to this, I stumbled upon this I have discovered It absolutely useful and it has aided me out loads. I hope to contribute & help other users like its helped me. Good job. match dating https://onlinedatingtind.com/
Tue May 04 2021, 08:34 PM
Chastity
Hi there! I could have sworn I've been to this site before but after browsing through some of the post I realized it's new to me. Anyways, I'm definitely glad I found it and I'll be book-marking and checking back frequently! check my score https://creditscorecheckn.com
Tue May 04 2021, 06:39 PM
Clarence
What's up everyone, it's my first go to see at this web page, and post is really fruitful in support of me, keep up posting these types of articles. Best Credit Score https://creditscoresids.com

Downloads

Comments

Mirza123
Thu Jun 25 2020, 03:46 PM
eunicelove124
Mon Jun 22 2020, 03:03 PM
cerouno
Tue Jun 16 2020, 05:10 PM
Marce
Sat Jun 13 2020, 09:43 PM
Davidthils
Thu May 21 2020, 12:44 PM
Jakeror
Thu May 21 2020, 01:28 AM
motorCar
Wed May 20 2020, 07:05 PM
Vordrync
Wed May 20 2020, 11:52 AM

Online

Guests: 104, Members: 0 ...

most ever online: 182184
(Members: , Guests: 182184) on 06 Aug 2010: 05:37 AM

Members: 38215
Newest member: Mirza123